AEG L77480FL User Manual

L 77480 FL EN User manual

ProgrammeTempera-tureType of loadMax. weight of loadCycle de-scriptionFunctionsCottons +Prewash95° - ColdWhite and coloured cotton withheavy level of

ProgrammeTempera-tureType of loadMax. weight of loadCycle de-scriptionFunctionsSpin / Drain5)0°All fabrics.The maximum load of the laun-dry is related

4) The wash and spin phase is delicate to prevent the creases of the laundry. The applianceadds some rinses.5) The default phase of the spin speed is

Make sure that no laundry stays betweenthe seal and the door. There is a risk ofwater leakage or damage to the seal orlaundry.8.2 FILLING THE DETERGEN

Check the position of the flap1.Pull out the detergent dispenser un-til it stops.2.Press the lever down to remove thedispenser.3.To use powder deterge

5.Press button 4 to start the pro-gramme. The indicator of button 4is on.The appliance adjust auto-matically the cycle time to thelaundry you have put

saving function automatically deacti-vates the appliance.When you activate the applianceagain, the display shows the setof the last performed pro-gram

gramme temperature and the level ofsoil.• If you use liquid detergents, do not setthe prewash phase.• If your appliance does not have thedetergent dis

10.4 Door sealRegularly examine the seal and removeall objects from the inner part.10.5 DrumRegularly examine the drum to preventlimescale and rust pa

10.7 Drain pumpRegularly examine the drainpump and make sure that it isclean.Clean the pump if:• The appliance does not drain the wa-ter.• The drum ca

CONTENTS1. SAFETY INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32. TECHNI

7.Remove fluff and objects from thepump.8.Make sure that the impeller of thepump can turn. If this does not oc-cur, contact the service centre.129.Cle

4.Remove the inlet hose behind theappliance.5.Clean the filter in the valve with astiff brush or a towel.45°20°6.Install again the inlet hose. Makesur

• - The appliance does not drainthe water.• - The appliance door is open ornot closed correctly.• - The anti-flood device is on.WARNING!Deactivate the

Problem Possible cause Possible solution The filter of the drainpump is blocked.Clean the filter of the drainpump. Refer to 'Care and clean-ing&

Problem Possible cause Possible solution You did not removestubborn stains beforeyou wash the laundry.Use special products to removethe stubborn stai

4.Remove the internal film.5.Open the door. Remove the poly-styrene piece from the door sealand all the items from the drum.6.Put one of the polystyre

9.Remove the power supply cable andthe drain hose from the hose hold-ers.10.Remove the three bolts. Use the keysupplied with the appliance.11.Pull out

12.2 Positioning and levellingx4• Install the appliance on a flat hardfloor.• Make sure that carpets do not stopthe air circulation below the applianc

• Connect the water inlet hose to thecold water tap with ¾” thread.CAUTION!Make sure that there are no leaksfrom the couplings.Do not use an extension

• On the edge of a sink.• Make sure that the plastic guide can-not move when the appliance drains.Attach the guide to the water tap orthe wall.• To a

1. SAFETY INSTRUCTIONS1.1 Conditions of useThis appliance is intended to be used inhousehold and similar applications suchas:• Farm houses.• By clien

the same meaning referred to inthe ACL;b)‘ACL’ means Trade PracticesAmendment (Australian Consum-er Law) Act (No.2) 2010;c)‘Appliance’ means any AEGpr

– incomplete or improper instal-lation– incorrect, improper or inappro-priate operation– insect or vermin infestation– failure to comply with any ad-d

FOR SERVICEor to find the address of your nearest state service centre in AustraliaPLEASE CALL 1300 363 664OR EMAIL [email protected]

ENGLISH 33

34www.aeg.com/au

ENGLISH 35

www.aeg.com/au132931132-A-232013

1.6 Installation• The appliance is heavy, be carefulwhen you move it.• Do not transport your appliance with-out the transit bolts, you can damageinter

Electrical connection: VoltageOverall powerFrequency230-240 V2200 W50 HzLevel of protection against ingress of solid particlesand moisture ensured by

1 2341SpannerTo remove the transit bolts.2Plastic capsTo close the holes on the rear sideof the cabinet after the removal ofthe transit bolts.3Anti-fl

5.3 Display 3A B C DThe display shows:A • The maximum temperature of the programme.B • The default spin speed of the programme.•'No Spin'1)

D • The programme timeWhen the programme starts, the time decreases with steps of 1 mi-nute.• The delay startWhen you press the delay start button, th

Spin phase is off.'Rinse Hold' function ison.5.10 Temperature button 10Press button 10 to change the defaulttemperature.- - = cold water5.11