on 09-22-2013 9:07 AM
Hi,
have you ever tried to run RSA3 in ECC with the datsource 2lis_11_VAHDR?
Even with no setup table filled, you will get an answer if the datasource is properly available in ECC.
If this will not help, go and check if structure MC11VA0HDR and the customer include is active.
BR
Maik
You must be a registered user to add a comment. If you've already registered, sign in. Otherwise, register and sign in.
Hi Sanket,
Can you please verify your Datasource 0FI_GL_4 where had used ZZBKTTX1 instead of ZZBKTTXT.
I presume that it should be CMOD of Transaction Data.
Thanks,
SB.
You must be a registered user to add a comment. If you've already registered, sign in. Otherwise, register and sign in.
This message was moderated.
You must be a registered user to add a comment. If you've already registered, sign in. Otherwise, register and sign in.
Hi Sanket,
Is your ECC system is connected to BW system. also if source system is not connected to BW system you may get an error like u mentioned.
Check like this for ur ECC connection .... -> go to bi side under the infoprovider tab ->select source system->in that R.Click on ur Ecc system click on check option ,u will get a display message though connection present or not.and if it is not activated then click on activate button.
Regards,
Shyamala
You must be a registered user to add a comment. If you've already registered, sign in. Otherwise, register and sign in.
Hi
Your ECC - BW connection is not the problem. Make sure your datasource is active. Go into LBWE and click on "Structure" from 2lis_11_VAHDR. Then change ZZBKTXT1 to ZZBKTXT. See if your structure definition is consistent after that change. Then you can activate it and your problem should be solved.
Martin
You must be a registered user to add a comment. If you've already registered, sign in. Otherwise, register and sign in.
Hi Sankeet,
Please check below points at source system side.
1. Have you activated respective data source from RSA5?
2. If yes then Go to RSA6, click on relevant data source.copy the extract structure. or
3. Go to LBWE, select application, expand, choose your data source.
a. Do the maintenance by clicking on maintenance.(i.e add required fields from left to right side)
b. Click on data source, do the selections and hide which you needed.
c.Click on activate.
Ex: watch below options, need to active your data source here also
4. Once you done above steps, go Tx - LBWE, delete setup tables of your application and fill thru Go to Tx - OLI7BW.
If your new bi, search on google with LO extraction steps, you will get lots of docs.
Thanks
You must be a registered user to add a comment. If you've already registered, sign in. Otherwise, register and sign in.
yes , wt ever sushant said is correct have you tried?
You must be a registered user to add a comment. If you've already registered, sign in. Otherwise, register and sign in.
again activate that 2 d.s and check it once
You must be a registered user to add a comment. If you've already registered, sign in. Otherwise, register and sign in.
check in bw system either that d.s is availble r not
You must be a registered user to add a comment. If you've already registered, sign in. Otherwise, register and sign in.
go to rsa9 and check either those 2 d.s are they maintained with request r not
You must be a registered user to add a comment. If you've already registered, sign in. Otherwise, register and sign in.
have you checked rfc con b/w ecc to bi
You must be a registered user to add a comment. If you've already registered, sign in. Otherwise, register and sign in.
Is your ECC system connected BW system. You may get this error (Error 2.jpg) also if source system is not connected to BW system.
You must be a registered user to add a comment. If you've already registered, sign in. Otherwise, register and sign in.
Hi
Your ECC - BW connection is not the problem. Make sure your datasource is active. Go into LBWE and click on "Structure" from 2lis_11_VAHDR. Then change ZZBKTXT1 to ZZBKTXT. See if your structure definition is consistent after that change. Then you can activate it and your problem should be solved.
Martin
Hi sankeet,
Have you added any customized fields in that standard d.s (Customer Exit).
Regards,
Giri
You must be a registered user to add a comment. If you've already registered, sign in. Otherwise, register and sign in.
Hi,
Its mean your datasource is not in active status. As mentioned by Venu, Check in RSA6.
Regards,
Sushant
You must be a registered user to add a comment. If you've already registered, sign in. Otherwise, register and sign in.
Hi Sanket,
Check the status of the data source of application component 11 in RSA6 i.e. whether the data source is in activated or not. If data source is not activated first activate it and the try to fill the setup tables.
Once data source is activated and setup table is filled you can check in RSA3.
Hope this helps.
Best Regards,
Venu Gopal K
You must be a registered user to add a comment. If you've already registered, sign in. Otherwise, register and sign in.
User | Count |
---|---|
83 | |
11 | |
10 | |
8 | |
7 | |
7 | |
6 | |
6 | |
5 | |
5 |
You must be a registered user to add a comment. If you've already registered, sign in. Otherwise, register and sign in.