Access WLAN Flash LED Problems Upper PBA This document is Sony Ericsson confi dential and should be treated as confi dential in accordance Main Camera Problems Slider Flex Module with the agreement with Sony Ericsson. This document is intended for use by authorized service...
Fluke 83 or similar Location: CSPN – Repair Instructions – Mechanical – Tool Catalogue – RepairToolsCatalogue.pdf Note! The 0, 64 mm Test Probes is recommended by Sony Ericsson when the DMM is in use. See Picture 1. Picture 1 1230-1858 rev. 1...
Page 5
ABOUT Equipment List SEMC Troubleshooting Manual W995 Power Cable RED to Power Supply Channel 1 (VBATT) Step 3: Maximum Length: 1m Cut off insulating material from inside of the charger plug according to Picture 8. Location: CSPN – Repair Instructions – Mechanical – Tool Catalogue – RepairToolsCatalogue.pdf...
Page 6
ABOUT Equipment List SEMC Troubleshooting Manual W995 Test SIM GSM/UMTS Connections Instructions for the Dummy Battery One Test SIM GSM/UMTS is needed to perform Current Consumption Test, see Picture 14. Location: CSPN – Repair Instructions – Mechanical – Tool Catalogue – RepairToolsCatalogue.pdf This setup is correct when the Dummy Battery is in use.
TROUBLESHOOTING Power On/Off Problems - Dead Phone Problems SEMC Troubleshooting Manual W995 Power On/Off Problems Dead Phone Problems part 1 START Note! Before following this guide check if C4203 is Short Circuit. If Yes Replace START C4203. If not go to step 1.
Page 8
TROUBLESHOOTING Dead Phone Problems SEMC Troubleshooting Manual W995 Dead Phone Problems part 2 Dead Phone Problems part 3 START START NOTE ! NOTE ! Before following this guide the Before following this guide the Dead Phone Problems part 2 TRS guide...
TROUBLESHOOTING Opto Sensor Problems - On Off Key Problems SEMC Troubleshooting Manual W995 Opto Sensor Problems On/Off Key Problems START START Step 1: Replace Slider Flex Assy and retest the Phone If successful claim Slider Flex Assy Load ETS SW into the Phone if not go to step 2.
TROUBLESHOOTING Numeric Keyboard Problems - Navigation Keys Problems SEMC Troubleshooting Manual W995 Numeric Keyboard Problems Navigation Keys Problems START START Load ETS SW into the Phone Step 1: Use TRS Fixture Go to Service Tests Menu and perform Keyboard Test...
TROUBLESHOOTING Ope ration Keys Problems - Volume Up and Down Button Problems SEMC Troubleshooting Manual W995 Operation Keys Problems Volume Up and Down Button Problems START START Load ETS SW into the Phone Load ETS SW into the Phone Use TRS Fixture...
TROUBLESHOOTING Camera Button Problems - Walkman Key Problems SEMC Troubleshooting Manual W995 Camera Button Problems Walkman Key Problems START START Flash the Phone with the ETS SW Load ETS SW into the Phone Use the TRS Fixture Use the TRS Fixture...
TROUBLESHOOTING Numeric Keyboard and Navigation Keys Illumination Problems SEMC Troubleshooting Manual W995 Numeric Keyboard illumination Problems Navigation Keys illumination Problems START START Load ETS SW into the Phone Use TRS Fixture Load ETS SW into the Phone Use the TRS Fixture and Connect:...
TROUBLESHOOTING Operation LED Problems - Camera Button LED Problems SEMC Troubleshooting Manual W995 Operation LED Problems Camera Button LED Problems START START Load ETS SW into the Phone Load ETS SW into the Phone Use the TRS Fixture and Connect:...
TROUBLESHOOTING Music LED Problems - Trickle Charge LED Problems SEMC Troubleshooting Manual W995 Music LED Problems Trickle Charge LED Problems START START Load ETS SW into the Phone Use the TRS Fixture Load ETS SW into the Phone Use the TRS Fixture Display Holder and Connect:...
TROUBLESHOOTING Flash LED Problems SEMC Troubleshooting Manual W995 Flash LED Problems in Camera Mode Flash LED Problems in Torch Mode START START Load ETS SW into the Phone Step 1: Use the TRS Fixture Go to Service Test and perform the Main Camera Test...
TROUBLESHOOTING Main Camera Problems SEMC Troubleshooting Manual W995 Main Camera Problems part 1 Main Camera Problems part 2 START START Use Fault Trace SW and go to: NOTE ! Before following this guide the Main Camera Problems Load ETS SW into the Phone...
TROUBLESHOOTING VGA/VTF Camera Problems - Data Communication Problems SEMC Troubleshooting Manual W995 VGA/VTF Camera Problems Data Communication Problems START Step 1: START Load ETS SW into the Phone Step 2: Use Phone with the Signalling SW (SSW) Use the TRS Fixture...
TROUBLESHOOTING Charging Problems - USB/VBUS Charging Problems SEMC Troubleshooting Manual W995 Charging Problems USB/VBUS Charging Problems START START Step 1: Perform Charging Test successful go to Step 2. Use Phone with the Signalling SW (SSW) Step 2: Use the TRS Fixture and connect: VBATT...
TROUBLESHOOTING SIM Problems - Memory Stick Problems SEMC Troubleshooting Manual W995 SIM Problems Memory Stick Problems START START Step 1: Flash the Phone with EMMA SUCR SW and retest the Phone Load ETS SW into the Phone if successful claim SW Flash, if not go to Step 2.
TROUBLESHOOTING Microphone Problems - Earphone Problems SEMC Troubleshooting Manual W995 Microphone Problems Earphone Problems START START Step 1: Load ETS SW into the Phone Replace Slider Flex Assy and retest the Phone Use TRS Fixture If successful claim Slider Flex Assy Connect: VBATT and DCIO/SEPI If not go to Step 2.
TROUBLESHOOTING Loudspeaker Problems SEMC Troubleshooting Manual W995 Loudspeaker Left Problems Loudspeaker Right Problems START START Load ETS SW into the Phone Load ETS SW into the Phone Use the TRS Fixture Use the TRS Fixture Connect: VBATT and DCIO/SEPI Connect: VBATT and DCIO/SEPI...
TROUBLESHOOTING Handsfree (PHF) Problems SEMC Troubleshooting Manual W995 Hands-Free (PHF) Connection Problems Hands-Free (PHF) Aux Microphone Problems START START Note ! Before starting this guide check that the Hands-Free (PHF) Connection is Ok. Power On the Phone Use Hands-Free (PHF) Set...
TROUBLESHOOTING Handsfree (PHF) Problems - Audio Jack Problems SEMC Troubleshooting Manual W995 Hands-Free (PHF) Aux Earphone Problems Audio Jack Detection Problems START START Note ! Before following this guide make sure that the Load ETS SW into the Phone Hands-Free (PHF) Connection is working properly.
Page 26
TROUBLESHOOTING Audio Jack Problems SEMC Troubleshooting Manual W995 Audio Jack Microphone Problems Audio Jack Output Problems START START Load ETS SW into the Phone Note ! Use TRS Fixture Before starting this guide check that the Audio Jack Detection is Ok.
TROUBLESHOOTING FM Radio Problems - Bluetooth Problems SEMC Troubleshooting Manual W995 FM Radio Problems Bluetooth Problems START Step 1: START Flash the Phone with the EMMA SUCR SW and retest the Phone If successful claim SW Flash If not go to Step 2.
TROUBLESHOOTING WLAN Problems - GSM Network Problems SEMC Troubleshooting Manual W995 WLAN Problems GSM Network Problems START START Step 1: Step 1: Flash the Phone with the EMMA SUCR SW and retest the Phone Replace Main Antenna and retest the Phone...
START START Note! Note! Can only be used for W995 phones with WCDMA BAND I, II or V Can only be used for W995 phones with WCDMA BAND VIII support Step 1: Step 1: Load ETS SW into the Phone...
TROUBLESHOOTING Real Time Clock - Slide Sensor - Video Companion Chip Problems SEMC Troubleshooting Manual W995 Real Time Clock Problems Video Companion Chip Problems START Load ETS SW into the Phone START Use the TRS Fixture Connect: VBATT and DCIO/SEPI...
TROUBLESHOOTING System Connector Protection Test - Current Consumption Test SEMC Troubleshooting Manual W995 System Connector Protection Test Current Consumption Test Step 1: Perform the Ohm measurements by using the DMM instrument (Fluke). Insert a Local SIM Card and use the phone with the Signalling SW (SSW).
Page 34
SEMC Troubleshooting Manual W995 Max TX Power GSM 900 MHz Max TX Power WCDMA BAND II Note! Valid only for the W995 with WCDMA BAND II support. Fault Trace SW settings: TX and RX GSM Fault Trace SW settings: GSM Mode Settings:...
TROUBLESHOOTING Backup Capacitor Test - Charging Test SEMC Troubleshooting Manual W995 Charging Test Backup Capacitor Test To perform this test use: To perform this test use: Phone with the ETS SW Phone with the Signalling SW (SSW) Power Supply Channel 1 VBATT: Instrument settings: Voltage: 3.8V, Limiter: 2A...
TROUBLESHOOTING ASIC Revision Test SEMC Troubleshooting Manual W995 ASIC Revision Test Note! The Keypad Scan Test must be Deactivated during this test. Purpose: Verify that the ASIC is correctly mounted, the communication works and that the revision is correct. The tested ASICs are:...
MEASUREMENT POINTS System Memories SEMC Troubleshooting Manual W995 Even if these pins (EMIF) are left unconnected, they are still active due to PoP interface. N2010 KAJSA_BOTTOM_APP_EMIF_A_9_24 KAJSA_BOTTOM_SYSTEM_LEVEL KAJSA_BOTTOM_APPLICATION MEMORY_IF(EMIF2) AP_D00 AP_A01 AP_D01 AP_A02 AP_D02 AP_A03 AP_D03 AP_A04 AP_D04 AP_A05 AP_D05...
MEASUREMENT POINTS System PoP IF SEMC Troubleshooting Manual W995 Kajsa Pop Top and Memory PoP connection Not to be included in packaging TOP_SH_DATA_BUS TOP_APPLICATION_DATA_BUS N2010 N2020 KAJSA_TOP_SH_EMIF_B_1_5 KAL00900MX-AJ55_MCP_POP_SDRAM_EMIF1 N2020 N2010 Kajsa-PoP_top-SYSTEM-LEVEL 2GbitNANDx8+128Mbitx16+512MbitSDRAMx16 KAL00900MX-AJ55_MCP_POP_NAND_EMIF2 KAJSA_TOP_AP_EMIF_B_2_5 KAJSA_SHARED_MEMORY_IF(EMIF1) SHAREDMEMORYIF(EMIF1) Kajsa-PoP_top-SYSTEM-LEVEL 2GbitNANDx8+128Mbitx16+512MbitSDRAMx16 TOP_SH_D00 T_B7...
FUNCTIONAL OVERVIEW Technical Description SEMC Troubleshooting Manual W995 W995 Function Overview Networks W995: GSM/GPRS/EDGE 850/900/1800/1900 UMTS/HSUPA 900/2100 W995a: GSM/GPRS/EDGE 850/900/1800/1900 UMTS/HSUPA 850/1900/2100 Note! The Network support depends on variant and market. Features Camera 8.1 megapixel camera Auto focus Up to 16x digital zoom...
Page 89
W995 Design Hardware Overview Auto rotate Picture wallpaper Platform Information Wallpaper animation The W995 and W995a are using the U365 platform provided by Ericsson Mobile Platform (EMP). Entertainment Media The U365 Platform Block Diagram Overview: YouTube™ 3D games Motion gaming...
Page 90
FUNCTIONAL OVERVIEW Technical Description SEMC Troubleshooting Manual W995 Baseband Part Functional Blocks of the Analog Baseband Controller: Analog Baseband Controller N2000 (Vera) This component is not replaceable on SL 4 because Baseband calibration is required. The analog baseband controller is the main power management circuit. It has converters and regulators that generate a number of supply voltages, each optimized for its load.
Page 91
FUNCTIONAL OVERVIEW Technical Description SEMC Troubleshooting Manual W995 Charger Control Connection Diagram of the Analog Baseband Controller: A programmable charger is used for battery charging. Limits can be set for the output voltage at CHSENSE- and the output current from DCIO through the sense resistor to CHSENSE-.
Page 92
FUNCTIONAL OVERVIEW Technical Description SEMC Troubleshooting Manual W995 Resistance Identification and Temperature Measurement CODEC Overview The resistance identification mode utilizes the constant current source to feed the battery The CODEC is encoding analog audio signals and analog voice signals into digital signals data output while monitoring the voltage at the battery data node with general purpose using Analog to Digital converters (ADCs).
Page 93
FUNCTIONAL OVERVIEW Technical Description SEMC Troubleshooting Manual W995 CODEC CCO Voltage Source Digital Baseband Controller (CPU) There is an internal voltage source CCO that provides the necessary drive current for N2010 (Kajsa) electret microphones. The voltage source is I²C programmable to 2.2 V or 2.4 V. The This component is not replaceable on SL 4 because Baseband calibration is required.
Page 94
FUNCTIONAL OVERVIEW Technical Description SEMC Troubleshooting Manual W995 Application Subsystem The functional blocks of the Digital Baseband Controller: The Application subsystem contains functionality related to functions such as MMI, graphics, audio and memory media. The control CPU is an ARM926 with three external memory interfaces, one shared with the Access subsystem and two dedicated for the Application subsystem.
Page 95
FUNCTIONAL OVERVIEW Technical Description SEMC Troubleshooting Manual W995 Radio Part Frequency Generation The 26 MHz reference signal is used as the reference for the on-chip synthesizers. To cover the required frequency range, the integrated Voltage Controlled Oscillator (VCO) Antenna operates at twice the frequency for band 1800/1900/2100, and at four times the desired The mobile system antenna interface connects the Wideband Code Division Multiple frequency for band 800/900.
Page 96
FUNCTIONAL OVERVIEW Technical Description SEMC Troubleshooting Manual W995 Ericsson RF 3300 Block Diagram: RF System Control The access side of the digital baseband controller controls the overall radio system. In both EDGE/GSM/GPRS and WCDMA air interface mode, the digital baseband controller controls the radio system through a three-wire serial bus.
Page 97
FUNCTIONAL OVERVIEW FUNCTIONAL OVERVIEW Technical Description SEMC Troubleshooting Manual W995 EGSM 900: filter is amplified by a VGA to the optimal input range for the A/D converter. Further RX Frequency Range: 925,2 MHZ – 934,8 MHZ channel filtering is done in the digital part. The digital part demodulates the GFSK, Channel Range RX: 975 –...
Page 98
FUNCTIONAL OVERVIEW SEMC Troubleshooting Manual W995 generated from this clock. However, when audio is transferred between the application A-GPS Block Diagram: and the access subsystems, the MCLK is used. Master Clock (26 MHz) The 26.00 MHz VCXO-based MCLK is distributed as a square wave signal from the GSM/EDGE circuit.
Page 99
FUNCTIONAL OVERVIEW SEMC Troubleshooting Manual W995 WLAN device or BT device gets the antenna is Packet Traffic Arbitration (PTA). WLAN LD configures the PTA during startup of the WLAN device. All PTA parameters are stored in GDFS. The PTA is configured to prioritize BT traffic if it is a BT high request. All WLAN traffic should have priority before any BT traffic that is categorized as BT low requests.
APPENDIX Replaceable Components SEMC Troubleshooting Manual W995 Position Component Part no. Comments Page N1210 IC Linear 1203-5870 P HA N1211 P HA IC Vreg PLP1820-6 1204-5903 Replaceable Components N1400 A-GPS 1200-0700 P HA N1410 IC Amp MicroDFN-6 1215-1892 P HA EXPLANATION OF ABBREVIATIONS USED IN THE COLUMN ‘COMMENTS’...
APPENDIX Components - B1400, B2100, B2400, B3100, B4200 SEMC Troubleshooting Manual W995 B1400 Osc TCXO 27,456 MHz 1200-7847 B2400 IC 1220-4470 0.28 0.1 0.12 0~0.07 0.9 0.15 Max0.55 1.45 0.1 Unit:mm B3100 Microphone 1210-7410 P IN C O N N E C T IO N...
APPENDIX Components - L4400, N1210, N1211 SEMC Troubleshooting Manual W995 L4400 Ind WW 2.2uH 20% 2.8x3.0x1.2 1215-2143 N1210 IC Linear 1203-5870 Pin Configuration T ypical Operating Circuit TOP VIEW REFBP AGND REFIN PGND BATT 0.4V TO V 2.7V TO 5.5V...
APPENDIX C omponents - N2420 SEMC Troubleshooting Manual W995 N2420 IC IF ISP1508 ES3 (3.5*3.5*0.8) 1200-1694 is in power down • When this pin is active, ULPI pins will operate normally. Pin Diagram If this pin is not in use, connect to VCC(I/O) directly.
ITP SW. Using this software you can control most parts and functions of all Sony Ericsson mobile phones. It is a Note: There are some differences in the user interface depending on the phone project file loaded.
Page 117
APPENDIX Troubleshooting Software Documentation SEMC Troubleshooting Manual W995 Equipment Setup Power Supply Channel 2 DCIO/SEPI Cable Connection Setup Note: The Power Supply Channel 1 (VBATT) must allow reverse current. Note: During calibration the accurate voltage from VBATT must be within ±0.015 V. If this is not Note: The maximal cable length between the Power Supply Channel 1 VBATT and the dummy battery fulfilled it will cause a faulty calibration.
Page 118
APPENDIX Troubleshooting Software Documentation SEMC Troubleshooting Manual W995 System Requirements GSM Radio Settings Note: Before start using the Troubleshooting Software, the phone must be flashed with ITP SW. Used for Channel and Power Level control of the selected GSM Band. The TX and RX frequency value for selected band and channel will be presented in the TX and RX frequency box.
Page 119
APPENDIX Troubleshooting Software Documentation SEMC Troubleshooting Manual W995 Fast select channels VCXO Control Set High Channel: The High Channel for selected WCDMA Band will be set by the Troubleshooting SW. Used to fine tune the VCXO to MCLK frequency by calibrating the DAC that sets the VCXO control voltage.
Page 120
APPENDIX Troubleshooting Software Documentation SEMC Troubleshooting Manual W995 Examples of different FM Radio Test setups in the Troubleshooting Software Audio output: Picture 11 Picture 12 Earphone is the internal Earpiece speaker of the unit. AUX earphone connected to the system connector.
Page 121
APPENDIX Troubleshooting Software Documentation SEMC Troubleshooting Manual W995 Current Calibration Memory stick test checks the communication with the Memory stick card. The test result (Passed or Failed) will be displayed in the info box. The Current Calibration test is similar to the Current Test for the charging algorithm in the factory Note: A Memory stick card must be inserted and a Memory card reader connected to run this test.
Page 122
APPENDIX Troubleshooting Software Documentation SEMC Troubleshooting Manual W995 Camera Door Test Vibrator Test ...timeout when reading Keyboard Scan Test Check the following items: Etc. Connection between Power Supply Channel 2 (DCIO) and SEPI A1 cable (Se picture 4, 5 and 6).
Page 123
APPENDIX Troubleshooting Fixture Setup Instructions SEMC Troubleshooting Manual W995 Troubleshooting Fixture Setup Instructions When the Camera 8 MPixel CMOS is in use, Place the TRS Fixture Display Holder into TRS Top-part overview of the TRS Fixture, see connect it directly to the PBA according to Fixture and secure by using the locking screws picture 1.
Page 124
APPENDIX Troubleshooting Fixture Setup Instructions SEMC Troubleshooting Manual W995 When using the Display, Navigation Keypad, Earphone, VGA-VTF Camera then use the TRS Fixture Display Holder and connect the Slider Secure the DCIO/SEPI Cable by using the Secure the SMK RF Probe with the RF Probe Close the TRS Fixture according to picture 13.
Page 125
APPENDIX Troubleshooting Fixture Setup Instructions SEMC Troubleshooting Manual W995 Connect the RF Cable Flexible to the GPS_RF Connector on the TRS Fixture according to picture 25. Picture 25 The PINs marked with GND text on the Bottom-part of the TRS Fixture can be used as...