1980 BMW R80/7

Make Model	BMW R 80/7
Year	1980-84
Engine	Four stroke, two cylinder horizontally opposed Boxer, pushrod operated 2 valves per cylinder.
Capacity	797.5 cc / 48.7 cu in.
Bore x Stroke	84.8 x 70.6 mm
Cooling System	Air cooled
Compression Ratio	9.2:1
Induction	2 x Bing constant depression carburetors
Ignition	Battery ignition
Alternator	Bosch 12 V/280 W
Spark Plug	Bosch W 175 T 30
Starting	Electric
Max Power	55 hp / 40 KW @ 6500 rpm
Max Torque	64 Nm / 6.5 kgf-m / 47 ft lb @ 5500 rpm
Clutch	Dry single plate, with diaphragm spring
Transmission	5 Speed
Final Drive	Shaft
Gear Ratio	1st 3.38 / 2nd 2.43 / 3rd 1.93 / 4th 1.67 / 5th 1.50
Rear Wheel Ratio	1:3.20 or 1 3.36
Front Suspension	Telescopic hydraulic forks.
Front Wheel Travel	200 mm / 7.3 in
Rear Suspension	Long swinging arm with adjustable strut.
Rear Wheel Travel	125 mm / 4.9 in
Front Brakes	2 x ∅260mm discs, 1 piston caliper
Rear Brakes	Single ∅200mm Drum
Front Wheel	1.85 - B19
Rear Wheel	2.50 - B18
Front Tyre	3.25 - H19
Rear Tyre	4.00 - H18
Dimensions	Length 2210 mm / 87.0 in Width 746 mm / 29.3 in Height 1080 mm / 42.5 in
Wheelbase	1465 mm / 57.67 in
Seat Height	810 mm / 31.9 in
Ground Clearance	165 mm / 6.49 in
Wet Weight	215 Kg / 473 lbs
Fuel Capacity	24 Litres / 6.3 gal

The BMW R80s evolved from the 750 and then just kept on evolving slowly, like most primitive forms of life.

was basically a bored-out R75. It had a duplex endless timing chain, contact breakers and mechanical advance/retard, wire wheels, fork gaiters, single front disc and a solid shaft

The British police were much taken with the bike, and, largely at their instigation, a second disc went on the front The front suspension was beefed up by reducing the damping rod holes from four to two. All engines were the S model with 9:1 compression ration,

Kinematics gearchange went on soon after, in a half-successful attempt to get a half-decent gearchange action. Cast wheels followed and brake calipers changed from ATE to Brembo. These changes crept up osmotically on the Beemer, but in late '79 came a major overhaul.

The seat changed to the sportier R90S style and the rear light became the current twin-bulb type. Changes also took place in the engine.

The timing chain changed over to a single-row item with split link, which is worth remembering as it takes half the time to replace compared to the duplex one.

The ignition was modified to get out of the way of water and oil, and was put in its own container and remotely driven, much like a car's distributor.

Fork gaiters departed and the shaft drive finally got a cam-type shock absorber.

Production finished in 1980, The engine continued in the R80G/S Paris-Dakar model, until the R80 was brought back in 1983, featuring some of the C/S mods.

BMWs are low-tech and low-stressed, so often prove to be ridiculously long-lived Later models will probably prove the better buy, if only because of their specification. Ignition may well prove troublesome on earlier models since the original points were at the front of the crankcase and could get water in from the front and oil from the rear.

Equally, the early duplex timing chains could take ten hours to replace even by a skilled mechanic, so the later models' single-link will prove easier to replace. Listen for clattering chains, which normally go about 40,000 miles.

On older models check for scuffed wiring loom and blocked breathers. Also look for worn rear wheel splines, as replacements are expensive. Wives can sometimes drop in at 50,000 miles or so on a very tired engine